Е-Публикации
Технически университет - София

Abstract: The structural reliability of pistons operating under severe thermo-mechanical loading strongly depends on the properties of the selected Al–Si alloy. This study presents an integrated experimental–numerical investigation of hypereutectic Al–Si alloys intended for piston applications. Phase constitution and silicon morphology were characterized by metallography and X-ray diffraction, while tensile testing provided mechanical properties for finite element modeling. The experimentally determined parameters were implemented in a three-dimensional piston model to evaluate stress distribution, deformation, and safety margins under maximum combustion pressure and maximum engine speed. The simulations revealed maximum von Mises stresses up to 150 MPa, with inter-alloy differences below 0.3%, indicating geometry-dominated stress behavior. The maximum displacement did not exceed 76 µm, varying by approximately 3% between alloys. In contrast, the minimum factor of safety ranged from 1.20 to 1.35, showing differences of up to 12%, primarily governed by yield strength and microstructural homogeneity. The results demonstrate that piston performance under combustion-dominated loading is strength-controlled rather than stiffness-controlled. The study provides quantitative insight into the structure–properties–performance relationship of hypereutectic Al–Si alloys and supports informed material selection for preliminary piston design.

References

1. Dimitrov E. Gigov B. Pantchev S. Michaylov P. Peychev M. A study of hydrogen fuel impact on compression ignition engine performance MATEC Web Conf. 2018 234 03001 10.1051/matecconf/201823403001
2. Mladenov G. Damyanov I. Saliev D. Ionchev E. Design of measurement system for vehicle emissions in real road conditions Proceedings of the 2022 30th National Conference with International Participation (TELECOM) Sofia, Bulgaria 27–28 October 2022 1 4 10.1109/TELECOM56127.2022.10017332
3. Mladenov G.D. Damyanov I. Saliev D.N. Valkovski T. Radev M. Measurement of vehicle emissions in real road conditions—Part II: Results and analysis AIP Conf. Proc. 2024 2980 050007 10.1063/5.0186011
4. Ambarev K. Nikolov V. Experimental study of toxic components in the exhaust gases during the operation of a car engine with gasoline and LPG Environ. Technol. Resour. Proc. Int. Sci. Pract. Conf. 2024 3 20 23 10.17770/etr2023vol3.7304
5. Savova-Mratsenkova M. Graph-analytic analysis of a road traffic accident involving an automobile and a bicycle AIP Conf. Proc. 2024 2980 050004 10.1063/5.0185110
6. Savova-Mratsenkova M. Palagachev G. Graph-analytic approach to determine the position of the initial impact in the event of pedestrian accidents IOP Conf. Ser. Mater. Sci. Eng. 2020 878 012042 10.1088/1757-899X/878/1/012042
7. Konakchiev H. Dimitrov E. Parameters Characterizing the Performance of Automotive Electronic Control Systems on Petrol Engine Emissions Eng. Proc. 2025 100 41 10.3390/engproc2025100041
8. Punov P. Milkov N. Danel Q. Perilhon C. Podevin P. Evtimov T. Optimization of automotive Rankine cycle waste heat recovery under various engine operating conditions AIP Conf. Proc. 2017 1814 020074 10.1063/1.4976293
9. Dobrev I. Massouh F. Danlos A. Todorov M. Punov P. Experimental and numerical study of the flow field around a small car MATEC Web Conf. 2017 133 02004 10.1051/matecconf/201713302004
10. Gechev T. Punov P. Driving strategy for minimal energy consumption of an ultra-energy-efficient vehicle in Shell Eco-marathon competition IOP Conf. Ser. Mater. Sci. Eng. 2020 1002 012018 10.1088/1757-899X/1002/1/012018
11. Ambarev K. Taneva S. Thermal and structural analysis of gasoline engine piston at different boost pressures Eng. Proc. 2025 100 38 10.3390/engproc2025100038
12. Lee Z.R. Ku P.X. Geometry design and optimization of piston by using finite element method J. Phys. Conf. Ser. 2021 2120 012013 10.1088/1742-6596/2120/1/012013
13. Dagar N. Sharma R. Rinawa M.L. Gupta S. Chaudhary V. Gupta P. Design and analysis of piston using aluminum alloy and composites in SolidWorks and ANSYS Mater. Today Proc. 2022 67 784 791 10.1016/j.matpr.2022.07.318
14. Singh A.R. Sharma P.K. Design, analysis and optimization of three aluminium piston alloys using FEA Int. J. Eng. Res. Appl. 2014 4 94 102
15. Wakshume E. Sufe G. Finite element analysis of engine pistons: Comparative assessment of aluminium and titanium alloys under combined thermal-structural loading Sci. Rep. 2025 15 41593 10.1038/s41598-025-25473-8 41285883
16. Singh U. Lingwal J. Rathore A. Sharma S. Kaushik V. Comparative analysis of different materials for piston and justification by simulation Mater. Today Proc. 2020 25 925 930 10.1016/j.matpr.2020.03.078
17. Roychoudhury A. Banerjee A. Mishra P.C. Khoshnaw F. An FEA material strength modelling of a coated engine piston Mater. Today Proc. 2021 44 1320 1325 10.1016/j.matpr.2020.11.387
18. Barbieri S. Mangeruga V. Giacopini M. The Effects of the Specific Material Selection on the Structural Behaviour of the Piston–Liner Coupling of a High Performance Engine SAE Technical Paper 2021-01-1235 SAE International Warrendale, PA, USA 2021 10.4271/2021-01-1235
19. Athithan A.K.K. Sivalingam K. Reddy P.N. Mamidi K.K. Hassan M.M. An analysis of the structural and thermal properties of the IC engine piston head with concave and convex shapes E3S Web Conf. 2024 564 11009 10.1051/e3sconf/202456411009
20. Kumar K. Design and Analysis of IC Engine Piston Using CATIA and ANSYS Master’s Thesis Maharshi Dayanand University Rohtak, India 2022
21. Zhang M. Tian Y. Zheng X. Zhang Y. Chen L. Wang J. Research Progress on Multi-Component Alloying and Heat Treatment of High Strength and Toughness Al–Si–Cu–Mg Cast Aluminum Alloys Materials 2023 16 1065 10.3390/ma16031065 36770071
22. Hu Z. Huo Q. Chen Y. Liu M. Chen X. Improving Mechanical Property of Hyper-Eutectic Al-Si Alloys via Regulating the Microstructure by Rheo-Die-Casting Metals 2023 13 968 10.3390/met13050968
23. Xia F. Dong X. Wang J. Duan H. Ma Z. Liang M. Microstructural Evolution and Tensile Properties of Al-Si Piston Alloys during Long-Term Thermal Exposure Metals 2024 14 535 10.3390/met14050535
24. Noga P. Cech R. Dvořák P. Janeček M. Buršík J. Microstructure and Mechanical Properties of Rapidly Solidified Al–Si Alloys Materials 2023 16 5223 10.3390/ma16155223 37569925
25. Bibik N. Metel A. Cherenda N. Sotova C. Astashynski V. Kuzmitski A. Melnik Y. Vereschaka A. Structure of Eutectic Al-Si Alloy Subjected to Compression Plasma Flow Impact Metals 2024 14 1415 10.3390/met14121415
26. Singhal V. Shelly D. Babbar A. Lee S.-Y. Park S.-J. Review of Wear and Mechanical Characteristics of Al-Si Alloy Matrix Composites Reinforced with Natural Minerals Lubricants 2024 12 350 10.3390/lubricants12100350
27. Chandra V.S. Krishna K.S.V.B.R. Ravi M. Sivaprasad K. Dhanasekaran S. Prashanth K.G. Mechanical and Tribological Behavior of Gravity and Squeeze Cast Novel Al-Si Alloy Metals 2022 12 194 10.3390/met12020194
28. Callegari B. Lima T.N. Coelho R.S. The Influence of Alloying Elements on the Microstructure and Properties of Al-Si-Based Casting Alloys: A Review Metals 2023 13 1174 10.3390/met13071174
29. Yang Y. Yu K. Li Y. Zhao D. Liu X. Evolution of nickel-rich phases in Al–Si–Cu–Ni–Mg piston alloys with different Cu additions Mater. Des. 2012 33 220 225 10.1016/j.matdes.2011.06.058
30. Jiang L. Zhao Z. Wang G. The Effects on Stability and Electronic Structure of Si-Segregated θ′Al Interface Systems in Al-Cu Alloys Coatings 2024 14 879 10.3390/coatings14070879
31. Mao F. Wei S. Ou L. Zhang C. Chen C. Wang X. Cao Z. Different Influences of Rare Earth Eu Addition on Primary Si Refinement in Hypereutectic Al–Si Alloys with Varied Purity Materials 2019 12 3505 10.3390/ma12213505 31731526
32. Xiao L. Yu H. Qin Y. Liu G. Peng Z. Tu X. Su H. Xiao Y. Zhong Q. Wang S. et al. Microstructure and Mechanical Properties of Cast Al-Si-Cu-Mg-Ni-Cr Alloys: Effects of Time and Temperature on Two-Stage Solution Treatment and Ageing Materials 2023 16 2675 10.3390/ma16072675
33. Šćepanović J. Asanović V. Radonjić D. Vuksanović D. Herenda S. Korać F. Bikić F. Mechanical properties and corrosion behaviour of Al-Si alloys for IC engine J. Serb. Chem. Soc. 2019 84 503 516 10.2298/JSC190306030S
34. Szymczak T. Gumienny G. Klimek L. Goły M. Szymszal J. Pacyniak T. Characteristics of Al-Si Alloys with High Melting Point Elements for High Pressure Die Casting Materials 2020 13 4861 10.3390/ma13214861
35. Jie L.L. Baig M.F. Mhd Noor E.E. Effects of Strontium Modification on Corrosion Resistance of Al-Si Alloys in Various Corrosive Environments Materials 2024 17 4923 10.3390/ma17194923 39410493
36. Jia Z. Zhou G. Zhou G.-W. Zhou H.-Y. Liu F. Ding L. Weng Y. Xiang K. Zhao H. Effects of Cu content and heat treatment process on microstructures and mechanical properties of Al–Si–Mg–Mn–Cu cast aluminum alloys Trans. Nonferrous Met. Soc. China 2024 34 737 754 10.1016/S1003-6326(23)66431-3
37. Hou J. Li H. Dong Q. Zhao Z. Microstructure and Properties of Laser-Remelted Al-Cu-Mn Alloy Metals 2025 15 693 10.3390/met15070693
38. Chai Y. Wen S. Wu X. Gao K. Wei W. Rong L. Huang H. Nie Z. Effects of Sn Microalloying on the Microstructure and Properties of Al-Mg-Mn-Si Alloy Metals 2025 15 1280 10.3390/met15121280
39. Herrera Hernández H. Mandujano Ruiz A. González Morán C.O. Miranda Hernández J.G. Flores Cuautle J.d.J.A. Morales Hernández J. Hernández Casco I. Microstructural and Electrochemical Study: Pitting Corrosion Mechanism on A390 Al–Si Alloy and Ce–Mo Treatment as a Better Corrosion Protection Materials 2024 17 3044 10.3390/ma17123044 38930413
40. Zhao J. Zhao T. Zhang Y. Zhang Z. Chen Z. Wang J. Chen M. Corrosion Behavior of the 2024 Aluminum Alloy in the Atmospheric Environment of the South China Sea Islands Coatings 2024 14 331 10.3390/coatings14030331
41. Qian Z. Hu Y. Fei C. Shu Z. Zhu S. Du Y. Finite Element Analysis of Thermal and Stress Fields of Diesel Engine Piston with GZO/YSZ Dual-Ceramic Layer Thermal Barrier Coating Coatings 2025 15 259 10.3390/coatings15030259
42. Han F. Wang H. Wang J. Wang J. Lin J. Dai H. Zhang J. Simulation Research on Cylinder Liner Shape and Position Tolerance under Thermo-Mechanical Load Processes 2024 12 1290 10.3390/pr12071290
43. Liu Y. Lei J. Deng X. Liu Y. Sun D. Zhang Y. Research and analysis of a thermal optimisation design method for aluminium alloy pistons in diesel engines Case Stud. Therm. Eng. 2023 52 103667 10.1016/j.csite.2023.103667
44. Li B. Dong Y. Gao H. Numerical Simulation and Experiment of Stress Relief and Processing Deformation of 2219 Aluminum Alloy Ring Metals 2023 13 1187 10.3390/met13071187
45. MAHLE GmbH Pistons and Engine Testing Springer Vieweg Wiesbaden, Germany 2012
46. Dochev B. Dimova D. Trojan K. Čapek J. Kamarska K. Chuchulska B. Investigation of the Influence of Alloying Elements Ni, Cr, Co and Mo on the Crystallization Process, Phase Composition and Corrosion Resistance of AlSi25Cu4Cr and AlSi25Cu5Cr Alloys Materials 2025 18 907 10.3390/ma18040907 40004432
47. ASTM E3-11 Standard Guide for Preparation of Metallographic Specimens ASTM International West Conshohocken, PA, USA 2017
48. ASTM E407-07(2015) Standard Practice for Microteaching Metals and Alloys ASTM International West Conshohocken, PA, USA 2015
49. EN ISO 6892-1:2019 Metallic Materials—Tensile Testing—Part 1: Method of Test at Room Temperature ISO Geneva, Switzerland 2019
50. ISO 6507-1:2018 Metallic Materials—Vickers Hardness Test—Part 1: Test Method International Organization for Standardization Geneva, Switzerland 2018
51. Ivanov V.K. Genov G.D. Guide for Course Design of Internal Combustion Engines Tehnika Sofia, Bulgaria 2002 954-03-0461-X (In Bulgarian)

Issue