Autors: Lengerov, A. D., Sabev, S. T., Paliiski, S. G.
Title: EXPERIMENTAL STUDY OF SURFACE ROUGHNESS IN VIBRO-IMPACT CUTTING OF OPTICAL SLUGS
Keywords: roughness, surface, experimental, study, optical slug

Abstract: In the article, experimental studies were carried out with the aim of determining the influence of different modes of vibro-impact cutting modes of optical slugs on the roughness of obtained surfaces. From the results obtained during the measurements and their mathematical processing are evaluated the average sizes and intervals and the parameters of the roughness of treated surfaces.

References

  1. S. Hambücker, “Technologie der Politur sphärischer Optiken mit Hilfe der Synchrospeed-Kinematik,” dissertation, Berichte aus der Produktionstechnik, Shaker Verlag, Berlin, Germany, 2001.
  2. Riemer, O.: “Trennmechanismen und Oberflächenfeingestalt bei der Mikrozerspanung kristalliner und amorpher Werkstoffe,” dissertation, University Bremen, Forschungsbericht Band 7, Shaker Verlag, Aachen, Germany, 2001.
  3. Voss R., Fundamentals of Carbon Fibre Reinforced Polymer (CFRP) Machining. Eigenössische Technische Hochschule Zürich (ETH): Zürich, 2017.
  4. K. Kumov, H. Metev, T. Kuzmanov. Geometric Accuracy in Machining Console Set Preparations. Mechanical Engineering and Mechanical Science, Technical University of Varna, vol. 26, pp. 127-132, ISSN 1312-8612, 2016.
  5. T. Zhao, J.M. Zhou, V. Bushlya, J.E. Stähl, Effect of cutting edge radius on surface roughness and tool wear in hard turning of AISI 52100 steel, Int. J. Adv. Manuf. Technol. 91, pp. 3611–3618, 2017.
  6. A.S. Vaykhinde, U.B. Bhor, V.V. Sachhe, S.P. Valte, S.B. Deokar, Review of effect of tool nose radius on cutting force and surface roughness, Int. Res. J. Eng. Technol. 4, pp. 699–703, 2017.
  7. Agmell, M.; Ahadi, A.; Gutnichenko, O.; Ståhl, J.E. The influence of tool micro-geometry on stress distribution in turning operations of AISI 4140 by FE analysis. Int. J. Adv. Manuf. Technol. 89, pp. 3109–3122, 2017.
  8. B. Denkena, A. Kroedel, T. Grove, Influence of pulsed laser ablation on the surface integrity of PCBN cutting tool materials, Int. J. Adv. Manuf. Technol. 10 pp. 1–12, 2018.
  9. Filip A C, Morariu C O, Mihail L A and Oancea G, Research on the Surface Roughness of Hardox Steel Parts Machined with an Abrasive Waterjet, STROJ VESTN-J MECH E 65(4) pp. 230-237, 2019.
  10. Dudutis J., Zubauskas L., Daknys E., Markauskas E., Gvozdaitė R., Račiukaitis G., Gečys P. Quality and flexural strength of laser-cut glass: Classical top-down ablation versus water-assisted and bottom-up machining. Opt. Express. 2022;30:4564–4582. doi: 10.1364/OE.447143.
  11. Grissa, R.; Zemzemi, F.; Fathallah, R. Three approaches for modeling residual stresses induced by orthogonal cutting of AISI 316L. Int. J. Mech. Sci. 135, pp. 253–260, 2018, https://doi.org/10.1016/j.ijmecsci.2017.11.029.
  12. Fan, Y.H.; Wang, T.; Hao, Z.P. Surface residual stress in high speed cutting of superalloy Inconel 718 based on multiscale simulation. J. Manuf. Process. 2018, 31, pp. 480–493, https://doi.org/10.1016/j.jmapro.2017.12.011.
  13. Wang, B.; Liu, Z.; Hou, X. Influences of Cutting Speed and Material Mechanical Properties on Chip Deformation and Fracture during High-Speed Cutting of Inconel 718. Materials 2018, 11, 461, DOI: 10.3390/ma11040461.
  14. Filmetrics, User Manual: Profilm3D Optical Profiler and Analysis Software (San Diego: Filmetrics), 2018.

Issue

Environment Technology Resources Proceedings of the International Scientific and Practical Conference, vol. 3, issue 14, pp. 145-148, 2023, Latvia, Rezekne Academy of Technologies, ISSN 1691-5402

Full text of the publication

Вид: публикация в международен форум, публикация в реферирано издание, индексирана в Scopus и Web of Science